When you drive your car, you rely on the tail lights to let other drivers know that you’re there. But what if they don’t work? What if they’re just not up to par? Well, fortunately, it’s not difficult to replace a tail light assembly. In this article, we will show you how to do it without any fuss. Whether you need a new tail light for your own car or you’re looking to repair a broken one, this article is for you. Sooner or later, your old tail light assembly will give out and you’ll want to replace it before it becomes a safety hazard.
What are the Different Types of Tail Lights?
There are a few different types of tail lights, each with its own specific purpose. Tail light assemblies can come in either a round or an oval shape, and they’re usually made from plastic or metal.
Round tail lights are typically used on cars and motorcycles, and they’re designed to give vehicles a more finished look. Oval tail lights are more common on trucks and buses, because they provide a wider range of visibility.
Both types of tail lights use either a high- or low-beams to illuminate the road ahead. High-beam headlights produce a bright light that’s perfect for driving at night, while low-beam headlights provide less brightness but are better for daytime driving.
How to Replace a Tail Light Assembly on a Car
Replacing a tail light assembly on a car is a straightforward task that can be done by any car owner with basic mechanical skills. The entire process typically takes about 30 minutes, and most drivers should be able to complete it without any assistance.
First, remove the cover from the tail light by unscrewing the two screws that hold it in place. Once the cover is removed, you will see the two light assemblies attached to the housing by wiring.
To replace one of the assemblies, unscrew the fastener that attaches it to the housing and gently pull it out. Be sure to hold onto the wire connector while doing this so you don’t lose it. Then, unscrew the second fastener and pull out the new assembly. If replacing both assemblies is required, insert one into the housing and screw it in place using screws provided, then screw on the other assembly.
Once both assemblies are in place, reattach the cover by screwing it back into place and reinserting the two screws.
Difficulty Level: Easy
If your car has a broken tail light assembly, you can replace it yourself. This is an easy DIY project that can be completed in just a few hours. You will need a few basic tools and supplies, and the replacement process is straightforward. read more
Difficulty Level: Moderate
If your tail light assembly is failing, you may be able to replace it yourself. This guide will outline the steps necessary for replacing the assembly, and provide a difficulty level rating.
1. Turn off the vehicle and remove the key from the ignition.
2. Disconnect the negative battery cable.
3. Remove the two screws that hold down the tail light assembly cover.
4. Slide the light assembly out of its housing.
5. Replace the light assembly using either a new or OEM part. Make sure to install the screws correctly in order to secure it in place.
6. Reconnect the negative battery cable and turn on the vehicle
Difficulty Level: Hard
If your car’s tail light assembly is not working, you may be able to replace it relatively easily. However, the procedure will require some disassembly of the vehicle. If you are comfortable doing so, replacing the tail light assembly may be a cost-effective solution to your car trouble.
To replace the tail light assembly on most cars, you’ll first need to remove the front bumper cover. On most cars, this is done by removing two screws near the hinge point on either side of the front bumper. Once the screws are removed, lift up on the bumper cover and pull it away from the car.
Next, you’ll need to remove two more screws that hold down a plastic trim piece above the rearview mirror. This trim piece can be gently pried off with a flathead screwdriver once these screws are removed. Be careful not to break this trim piece – it will obscure your view when replacing your tail light assembly later on.
Once those two pieces are removed, you’ll be able to access the rear view mirror andremove it (or detach it if it’s an option). Next, locate and remove four screws that hold down a metal bracket that supports both sides of the tail light assembly. After those screws have been removed, gently disconnect both ends of the tail light assembly from its mounting brackets.
Now you’re ready to replace your old tail light assembly with a new one! First, reinstall all of the original screws that were removed
Tips for Replacing a Tail Light Assembly
If you have a broken or damaged tail light assembly, it’s time to replace it. Here are some tips for replacing a tail light assembly:
1. Unplug the car battery and remove the tail light assembly.
2. If the housing is plastic, use a screwdriver to pry off the edge of the housing. If the housing is metal, Pry it off with a flathead screwdriver. There will be 2 tabs on each side that should come away easily.
3. Remove the bulb, lens, and reflector by unscrewing them from the housing. Save these items for later!
4. Reinstall all of the parts in reverse order-bulb first, then lens and reflector, followed by the housing. Make sure that everything fits properly before reattaching the wire harnesses and securing them with screws (you may need to reuse some of the screws from earlier).
5. Replace the car battery and test your new tail light assembly!
Conclusion
If you are like most drivers, your tail light assembly may have been damaged or gone out at some point in time. If this is the case, it’s important to replace the assembly as soon as possible in order to avoid getting pulled over and receiving a ticket. Here are a few tips on how to replace your tail light assembly without any trouble: ###