Driving at night can be a daunting task, especially when you’re trying to dodge potholes and other obstacles on the road. But if you ever find yourself stranded on the side of the road with a broken tail light, don’t panic. There are ways to fix it without having to go to a mechanic. In this article, we will teach you how to fix a tail light using simple tools and household items. From there, you will be able to get back on the road in no time and avoid costly repairs.
What You’ll Need
To fix a tail light, you will need:
-A screwdriver
-A Phillips head screwdriver
-A tail light cover
-Wire strippers
-An EL wire cutter or a small hair clipper
-Electrical tape
-RTV silicone (optional)
1. Remove the screws that hold the tail light cover in place. Be sure to note which screws are which as you remove them so that you can replace them correctly when you reattach the cover.
2. Remove the tail light by gently prying it off of the assembly it is attached to. If necessary, use a Phillips head screwdriver to unscrew the light from its mounting hole.
3. Strip both ends of the wire leading from the light bulb to the body of the vehicle approximately 1/4 inch from each end. Make sure not to cut into any wires that may be bundled together near where they enter and exit the bulb housing.
4. If using an EL wire cutter or hair clipper, carefully cut off one end of the EL wire while maintaining enough of a connection between each individual strand so that they will still function when reassembled.
5. Strip about 1/2 inch of electrical tape across one end of each wire leading from the bulb housing to where they were stripped in step 3. Twist each wire pair together once, then tape them up against each other with electrical tape. Be sure not to wrap too tightly – you just
How to Fix a Tail Light
If your tail light is not working, it may be due to a broken light bulb or a bad fuse. In some cases, the light can also be out because of damage to the housing or wiring. In any case, fixing a tail light is fairly simple and can be done by following these steps:
1) Disconnect the electrical connection from the tail light. This can be done by removing the screws that hold on the housing or by disconnecting the wires that run to the lightbulb.
2) Remove the old light bulb andreplace it with a new one. Make sure to install the new bulb in the same orientation as it was in before.
3) Reconnect the electrical connection and screw on the housing. Be careful not to tighten too much, as this could cause damage to the housing or wiring.
Common Problems with Tail Lights
Tail lights are one of the most common problems on vehicles. They can be a simple fix, but they can also be more complicated. Here are some of the most common problems with tail lights and how to fix them:
The light isn’t turning on
There are a few things you can check to see if the tail light is working. First, make sure that the light switch is turned on. Then, look at the light itself. If it’s not turning on, there may be something wrong with the connector inside the light or with the wiring going to it. You can test this by replacing the connector or wiring in the light.
The light is burned out
If the light is not turning on, then it’s probably burned out. Tail lights use a lot of electricity, so if they’re not working, there’s probably something wrong with the battery or circuit board. You can replace either of these components to get your tail light back up and running.
Troubleshooting Tail Lights
If your tail lights are not working, there are a few things you can do to troubleshoot the issue. First, check the fuse. If the fuse is intact and the lights still do not work, then it is likely that a wiring issue exists. Next, check for any broken or loose connections on the light bulb. Finally, inspect the light housing for damage or dirt buildup.
Conclusion
If your car’s tail light is not working, there are a few things you can do to try and fix the issue. First, check to see if there is any moisture or oil in the area where the light bulb goes into the headlight. If so, clean it up using a solution of water and detergent. Next, make sure that the connector on the end of the light bulb is securely plugged into the socket on the car. Finally, test whether or not the light works by turning it on and off several times while holding down the switch that turns it on and off. If everything seems to be in order, you may need to replace the light bulb.